| Note |
|---|
This article is written for Pally module Module for Doosan cobot |
| Info |
|---|
With the Pally module Module you create the complete waypoints in MyRobot.Cloud instead of on the cobot. Creating the waypoints is done by creating your pattern and run a complete simulation when using the backup of the installation/calibration. |
MyRobot.Cloud / Waypoints Generation
Sign in or sign up to MyrobotMyRobot.Cloud at https://www.myrobot-cloud-dev.herokuapp.com.
...
| Info |
|---|
As this is the Development stage bugs can occur. If you find any report them to Rocketfarm. |
| Note |
|---|
Only @rocketfarm.no and @doosan.com selcted email domains are whitelisted at the development stage. |
With your user and organization set up. Create a customer organization.
Upload Calibration / Installed Robot
Select customer to work with
One the customer organization dashboard, press
on Installed Robots
...
Select Doosan
Enter a name for your robot and press Upload Calibration File
Choose the generated calibration file from your robot
Once you’ve done this you should see your robot listed
| Info |
|---|
A popup that no license found is presented. You can ignore this. |
...
. If you will see information that the cobot does not have any license, you need to activate the license on this particular customer organization.
This means that we need correct end user information before generating the license in the first place
After activating the license you are ready for creating a pattern and generating waypoints.
Create Pattern
Back at the customer organizations press on the Patterns card.
A new dialogue should open where you enter your product dimensions and customize your pattern.
Select / Create Product
Either select an existing product or create a new product
Create new
Press + New Product
Enter name, product dimensions and label orientation
Press Save
Once you’re happy with your product press -> Next
...
Create pattern
| Info |
|---|
For more information on pattern generation visit: Product and patterns |
...
Once you’ve pressed Confirm you are redirected to the Pattern table where your patterns are listed.
Path Path Strategy
Back at the customer organizations press and go to Pally program settings on the Pally Path Strategy card.left meny. Then you can add new Pally path strategies.
A new dialogue should open where you can tune the path planning parameters.
Create Pally Path Strategy
Name your strategy
Adjust the Path Planning parameters. Description of the different parameters can be found below.
Adjust the Gripper settings. Description of the different parameters can be found below.
Once satisfied. Press → Confirm
...
Path Planning
...
Variable | Description |
|---|---|
Above pickup | Distance from pickup to above pickup position. |
Box free height | Distance from pickup to box free position. |
Box free auto | Box free height should not be smaller than the box height. |
Approach | Approach distance |
Approach auto | Approach distance can be recalculated for each box. |
High approach boost | High approach boost. Only in effect when placing boxes below conveyor height. Floating value: [0 → 1] 
|
Pallet edge | Pallet lip. Set to 0 if none. |
Smart Exit | Area to search for a smart exit waypoint. min x - Lower X limit max x - Upper X limit min y - Lower Y limit max y - Upper Y limit |
Gripper
Variable | Description |
|---|---|
Gripper rotation | The value can be either None, Two way or Four way. Representing the different ways a robot can pick the box. None: forward (the gripper direction at the calibrated pick position) 2-Way: forward and backward 4-Way: forward, backward, left, right |
Max grip | Currently not in use. |
Min grip quality | The minimum grip quality for calculating number of boxes to pick relative to gripper size. When the estimated grip quality drops below the minimum threshold, the program can decide to pick fewer boxes, use another gripper rotation at pickup, or even reduce the maximum allowed acceleration to guarantee box transport stability between the pick and drop position. Floating value from 0 and up. |
Foam height | Gripper foam (suction cup) squeezing length in meters. Default value 0.02. |
Length coverage | Minimum required fraction of the total length of each box covered by the gripper in multi-pick |
Grip rotation cost | Additional cost of each specific gripper rotation (0, 180, -90, +90) Default: [0, 30, 10, 10] |
Align to edges | Gripper-to-box edge alignment. Default: True Setting the value to False can be relevant for some custom grippers e.g. pinch grippers. Setting the value to False may cause accidental multipick of small boxes with large vacuum gripper. |
Generate Waypoints
From the customer organization’s dashboard press go to Pally programs on the Generated Waypoints cardleft meny.
Select your pattern(s).
Select your Calibration ( Installed Robot)
Select your Pally Path Strategy(ies)program setting
Press Confirm
Once the waypoint generation is finished you can download the generated .json
Download the file to a USB drive and upload the file on the robot according to the Pally Manual Upload patterns to the robot
...